The Multi-Channel Desk Station has an internal loudspeaker. A 3-pin XLR microphone connector on the front panel allows you to connect a stalk microphone (not supplied). On the back panel are two Ethernet LAN ports with an internal 100MB switch. There is also a GPIO connection located on the back of the device (2x in, 2x out).

The Green-GO Beltpack X features a high-resolution full colour OLED display which shows information about channels, cue signals and the different functions that are operated by the four buttons on the front of the Beltpack. These buttons can be configured to provide instant access to up to four channels. Two rotary encoders are located on either side of the Beltpack X, making it suitable for both left- and right-handed users. By pushing the encoders, the Beltpack X can answer the most recent audio source. The encoders can also be programmed to control various other functions, e.g. one encoder can be set up for level control while the other encoder controls channel selection. All matrix data is held within the device. The Beltpack X is powered through a Power over Ethernet connector located on the back. Also located on the back is a 4-pin XLR headset connector.

Please call for info.

Please call for info.

Please call for info.

Please call for info.

Please call for info.

Please call for info.

Please call for info.

Please call for info.

Please call for info.

Please call for info.

Please call for info.

Please call for info.

This unit incorporates an internal, worldwide voltage operation power supply than powers all the system. In case of a short circuit on any point of the line, the unit shuts down with automatic and instantaneous reset. Separate dual channels are provided with independent TALK and listen A-B balance. Link A-B switch enables line B to be joined to line A when required. A program Input to adapt balanced Mic and Line levels is provided with assign and volume controls. The headset microphone signal is available to drive P.A. systems. Relay contacts are provided that follows the P.A. key action, helping the installer to automate multiple tasks as Tally, switching speakers, cue lights... The unit incorporates, remote all Mic-Off (Mic-Kill) and all Buzzers-Off (Buzz-Kill) switches to both channels. The MULTICHANNEL LINK connection of master stations allows to carry out multichannel systems and use an only headphone for all the intercom lines. Internal Battery operation enabling short time emergency communications on Power dropouts. Relay contacts available NO/NC for multipurpose remote control, enabling Tally, radio station PTT, etc.

This unit incorporates an internal, worldwide voltage operation power supply than powers all the system. In case of a short circuit on any point of the line, the unit shuts down with automatic and instantaneous reset. Separate dual channels are provided with independent TALK and listen A-B balance. Link A-B switch enables line B to be joined to line A when required. A program Input to adapt balanced Mic and Line levels is provided with assign and volume controls. The headset microphone signal is available to drive P.A. systems. Relay contacts are provided that follows the P.A. key action, helping the installer to automate multiple tasks as Tally, switching speakers, cue lights... The unit incorporates, remote all Mic-Off (Mic-Kill) and all Buzzers-Off (Buzz-Kill) switches to both channels. The MULTICHANNEL LINK connection of master stations allows to carry out multichannel systems and use an only headphone for all the intercom lines. Internal Battery operation enabling short time emergency communications on Power dropouts. Relay contacts available NO/NC for multipurpose remote control, enabling Tally, radio station PTT, etc.

The Single Channel Beltpack unit was designed for intensive use in portable applications. An unbreakable plastic belt clip, enables easy and secure suitability. Call signalling is Dual, visual and audible for improving adaptability. The unit can be configured for dynamic or electret microphones enabling the use of different types of headsets and hands-free earpieces in the market.

The Single Channel Beltpack unit was designed for intensive use in portable applications. An unbreakable plastic belt clip, enables easy and secure suitability. Call signalling is Dual, visual and audible for improving adaptability. The unit can be configured for dynamic or electret microphones enabling the use of different types of headsets and hands-free earpieces in the market.

The new ALTAIR EM-202 beltpack, compatible with the E-200 intercom series, allows independent or simultaneous communications with both channels A and B. Call signalling is dual, visual and audible for improving adaptability. An unbreakable plastic belt clip, enables easy and secure suitability. The unit can be configured for dynamic or electret microphones enabling the use of different types of headsets and hands-free earpieces in the market.

The new ALTAIR EM-202 beltpack, compatible with the E-200 intercom series, allows independent or simultaneous communications with both channels A and B. Call signalling is dual, visual and audible for improving adaptability. An unbreakable plastic belt clip, enables easy and secure suitability. The unit can be configured for dynamic or electret microphones enabling the use of different types of headsets and hands-free earpieces in the market.